Granulation & Tableting - Online Training Recording

Course No. 21432



Dr Harald Stahl

Dr Harald Stahl


Prof Dr KArl Gerhard Wagner

Prof Dr KArl Gerhard Wagner

University of Bonn

Dr Michael Braun

Dr Michael Braun

Boehringer Ingelheim Pharma

Dr Jean-Denis Mallet

Dr Jean-Denis Mallet

Former Head of the Pharmaceutical Inspection Dpt. AFSSAPS


A thorough root cause analysis often reveals that compression issues such as capping, sticking and weight variations are related to the upstream granulating process. The objective of this intensive online training course is therefore to provide a deeper insight into functional relationships between granulation and tabletting in order to avoid such problems from the very beginning.

The online training Course also conveys a deeper understanding for tableting and granulating processes, including Scale-Up, which helps in avoiding problems or solving them in practice. This also complies with the GMP principle of understanding and controlling the critical parameters of manufacturing processes. An introduction to the different GMP requirements for manufacturing solid dosage forms worldwide is therefore also subject of this course.


Granulation and tableting are considered the most commonly used manufacturing processes in the pharmaceutical industry. Of course, a direct compression process is most preferred; in practice, however, an upstream granulation is usually required to obtain a favourable particle size distribution, flowability and compactibility. Different requirements for granulates call for different procedures or technologies. Nowadays, fluid bed, high-shear or dry granulation are the most commonly used processes. An important part of this course is therefore to introduce the different granulation methods, their basic principles and Scale-Up approaches. A deeper insight into process parameters and their influence on product properties is also part of the programme.

The holistic approach to granulation and tableting therefore aims at avoiding issues from the very beginning and to overcome problems at an industrial scale through in-depth process insights. A separate block of this seminar is dedicated to the issue of Trouble Shooting. Please bring your questions concerning manufacturing problems with you or send them in beforehand.

These challenges are met by new excipients, new control algorithms for tablet presses, laminations as well as special punches and dies. Having the presses run slower should be a last resort after all other options have failed.

Further topics of this training are the tableting of highly active materials, the implementation of recent validation requirements based on the example of tablet manufacturing as well as continuous manufacturing.

Target Group

This intensive online training course is designated for all professionals from Pharmaceutical Development, Production and QA/Regulatory Affairs, who are responsible for the development, the routine production or the Scale-Up and transfer of tableting processes.

Technical Details

To participate in an on demand training course or webinar, you do not need any software. The recordings are made available via a streaming server. In general, the recording is provided in MP4 format, which any PC (Microsoft Windows, Apple IOS) or tablet can easily display.

Timing and Duration:
When you register for the on demand Training course or webinar you can decide at what date you want to follow the training course online. For a 1-day training course you will have 2 days in which the stream is available (for 2-day training course 3 days and for a 3-day training course 4 days). Within in this timeframe you can start & stop the stream according to your needs.

In time before the scheduled date (your desired date) you will receive an e-mail from us with a link for direct participation as well as your log-in data.

Please be aware: The recording does not include the Q & A sessions.

Training Course Documentation and Certificate:
The presentations will be made available as PDF files via download shortly before the online training course. After the event, you will automatically receive your certificate of participation.


Fundamentals of granulation – what is a good granulate?
  • Reasons for granulation
  • Overview of the different granulation processes
  • Impact of the single processes on the granulate properties
  • Understanding the mechanisms of agglomeration
  • Characterisation of granulates
  • Excipients for granulation and their impact on product properties
Fundamentals of Fluidbed-Granulation
  • Design aspects and working principle of a modern fluidbed-dryer
  • Basic principle and advantages of fluidbed-granulation
  • Impact of process parameters on product properties
  • Process insights: how to run, control and design the process
Scale-Up of Fluidbed Granulation
  • Fundamentals of Fluidbed Granulation (process & technology)
  • Which process parameter influences which product quality attribute
  • How to scale-up?
  • Consequences for the quality critical attributes
High Shear Granulation: Fundamentals
  • Plant-geometry and -design
  • Process parameters (degree of filling, impeller speed, liquid saturation, process time)
  • Methods of drying
  • Special Case: Single-Pot-Granulation
High Shear Granulation: Scale-Up
  • Influence of impeller speed, liquid addition rate and wet massing time
  • Review of end point detection methods
  • Scale up trouble shooting
Fundamentals of Roller Compaction / Dry Granulation
Dry granulation is gaining more and popularity in the pharmaceutical industry as it may offer advantages like fast development and Scale-Up, usability in continuous manufacturing operations and improved process control
  • Design aspects of a modern roller compactor
  • Impact of process parameters like compaction force, gap, roll speed, roll surface, roll width and side seal system on ribbon properties
  • Principles of densification: solid fraction as critical material attribute
  • Scale-Up
Wrap-Up: Overview and comparison of the different granulation techniques - An Outlook
  • Which technique for which kind of product: viewpoint of development
  • Which technique for which product portfolio: viewpoint of production
  • Comparison of direct and indirect cost: viewpoint of management
  • Continuous Manufacturing
    • Factors for a 6-sigma granulation process
    • Which optimisation is possible by using continuous Granulation
    • Control of continuous processes
Tableting: Process, Equipment and Formulation
  • Physical fundamental of powder adhesion
  • Compressibility and compactibility of different materials
  • How to quantify these properties?
  • How to handle materials with unfavourable compression properties?
  • Parts of tablet presses: their function and their impact on product properties
  • Comparison of the different control philosophies
  • Measurement of the deformation behaviour by compression analysers
  • Overview and characterisation of the most important excipients used for compression
Scale-Up of tableting processes
  • Compression issues during Scale-Up and Transfer Quality by Design helps to overcome Scale-Up issues
  • Scale-Up and optimisation of compression processes
  • Constant dwell time as Scale-Up approach: theory and practice
  • Case studies
Global requirements for OSD operations
  • OSD Quality Attributes: from homogeneity to dissolution
  • Pharmacopoeias and OSD: main monographs
  • Requirements from the main guides: US, EU/PICS & WHO
  • Requirements from special chapters: US, UK and France
Handling of highly potent materials – Containment for tableting processes
  • How much containment is really needed
  • Identification of critical operations (with regards to exposition)
  • Comparison of different containment concepts
  • Examples of existing equipment
Validation of a tableting process
  • Main Pharmacopoeial descriptions for tablets
  • What are the main validation requirements
  • Tablets Quality Attributes and Tableting Critical Parameters
  • Establishing a protocol not forgetting intermediate steps
  • Running the process not neglecting secondary operations
  • Writing a clear and trustful Report
  • Following tablets stability issues
  • Conclusion
Trouble shooting in tableting processes: Sticking, Capping & Lamination
  • Reasons for tableting problems
  • Possible changes in upstream processes
  • How to improve compression properties
  • Tips and tricks for production: possible changes within the existing equipment and registration environment
Recording from 12-14 September 2023
Duration of Recording: 13h 4min


This course is part of the GMP Certification Programme "ECA Certified Technical Operations Manager" Learn more

ECA-Member*: € 2090,-
Regular Fee*: € 2290,-
EU/GMP Inspectorates*: € 1145,-
APIC Member Discount*: € 2190,-

(All prices excl. VAT). Important notes on sales tax.

* also payable by credit card
American Express Visa Mastercard

Further dates on-site
Further dates on-site
Not available
Further dates online
Further dates online
Not available

Do you have any questions?

Please contact us:
Tel.: +49 6221 8444-0

Woman with headset

Go back

Testimonials about our courses and conferences

“Fantastic course – I really enjoyed the interactive structure & greatly appreciate social activity.”

Anthony Cummins, Sebela Pharmaceuticals, Ireland
GMP Auditor Practice, September 2023


“Very well organized, information on point without being overwhelming.”

Eleni Kallinikou, Pharmathen
Live Online Trainng - Pharmaceutical Contracts - Febuary 2024


“Good overview of different types of agreements, good to see both the GMP and the legal angle”

Ann Michiels, Johnson&Johnson
Live Online Trainng - Pharmaceutical Contracts, Febuary 2024



“Well prepared presentations and good presenters. I also like the way of asking questions.”

Alexandra Weidler, Hookipa Biotech GmbH, Austria
Live Online Training – QP Education Course Module A, November 2023